Quantcast
Channel: Leviton Online Knowledgebase : Popular Discussions - Timers
Viewing all 6360 articles
Browse latest View live

LTB30 Timer Installation for Bathroom Fan

$
0
0
Hi guys,   I purchased a Leviton LTB30 and tried to installed it for my bathroom fan. However I'm confused by my bathroom fan wiring. I'm not sure if this is a 3 way or single pole configuration. This is the existing wiring. 3 sets of wires

VPT24-1P

$
0
0
VPT24-1P  Replacing a mechanical light timer which connected solely to a hot lead and the load lead (for lighting only).  Wired the new timer per diagram - hot box lead to black; box load lead to red; box neutral to white.  No LED, no

timer switch and GFCI

$
0
0
I bought a 6124H-W electronic timer switch a couple of years ago.  I have a circuit that runs from the house to the street with a post light, outlet, and low-voltage transformer feeding some path lights, and wanted to put the lights on a

Setting on off time correctly

$
0
0
This should be fairly simple. I want the lights to come on at sunset everyday, this seems fairly straightforward. I Wat the lights to turn off at the same time everyday, say 2am and not sunrise. How would I program that?   thanks in advance

VPT24-1PZ Stuck on Event 1???

$
0
0
I have 2 events programmed and I can't seem to get Event 2 to stay as the active event; it keeps staying on Event 1?? I followed the instructions but I can't seem to make the light switch to stay on Event 2??

VPT24-1P wiring diagram

$
0
0
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box but what do i hook up the red/yellow wire too? how

LTB30-1LZ - 3-way Wiring with Vizia + Matching Remote switch (w/LED) ISSUES

$
0
0
Hi,   I just install a LTB30-1LZ with the 3-way wiring with Vizia + Matching Remote switch (Step 4c in the instruction sheet) but I have a issue.   The Timer work and my lightswitch also work. I only have one wire with a load, I can't use the

Help installing VPT24-1P Timer switch

$
0
0
THis is what I am seeing inside my box in the wall -   A copper ground wire   A black wire A red wire   on this new unit I see the following   green wire - I am pretty certain this connects to the copper wire in the wall a black

VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.

$
0
0
Hi,   I installed this timer, and it's working.   I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm.  I like it.   My question is on what the offset setting is for?  Is it used to

VPT24-1PZ how to factory reset all setting

$
0
0
So I have problem   cuz I tryed to many time clock setting   but VPT24 clock goes wrong soon   How can I factory  reset all setting.   or   Is this VPT24 is broken???

Vizia VPT24

$
0
0
I bought this timer to control my exterior lights.  My exterior lights are controlled by 2 switches (3 way). I noticed on the box that it says to control the fixture from two locations I need the VPOSR.   Will it only work if I buy

VPT24 Installation

$
0
0
My existing light switch did not have a neutral connection, but I have tapped into the white (neutral?) wires inside the box.   Unfortunately, this has not done the trick as I cannot get the timer to work.  I am getting the Battery Power (no

VPT24 as a 3-way replacement

$
0
0
I am trying to use the VPT24-1P to replace an existing 3-way switch.  My existing switch, and the mate, are both 3-way toggle switches.  They have a Red, Black, Green and White connected to them, with a separate black & white line power in

How do I install a timer delay switch on an end of run?

$
0
0
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red.  It is an end of run switch, so the white wire is actually the hot wire and the black runs back to the lights.  How do I do it?

Question about installing the VPT24-1PZ

$
0
0
Hi,   I am attempting to install this switch but have run into some problems.  The switch is in a panel with two other switches.  One is a three way and the other two are single poles (at least I think they are as there are no other

Can the 6161T control a fan?

VPT24-1PZ how to factory reset all setting

$
0
0
So I have problem   cuz I tryed to many time clock setting   but VPT24 clock goes wrong soon   How can I factory  reset all setting.   or   Is this VPT24 is broken???

VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.

$
0
0
Hi,   I installed this timer, and it's working.   I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm.  I like it.   My question is on what the offset setting is for?  Is it used to

VPT24-1PZ without LED Indicator?

$
0
0
Is it possible to disable the LED indicator at the bottom of the VPT24-1PZ ?  I know that the remote switch is available with or without but I don't wish to have the LED active on the main unit.  If not is there a similar astronomical timer

Problem when installing VPT24-1P

$
0
0
I am trying to install a Leviton VPT24-1P Digital Timer Switch: Hi I'm trying to install the timer swtich on the right most light switch of a 3-light switch electric box. ----------------------------------------------------- Original box setup: From
Viewing all 6360 articles
Browse latest View live


Latest Images