Unable to Switch to Pro Mode
I installed in STD mode and then realized I should have done in PRO to use sun up / sun down. How can I switch to PRO? I tried holding SET and then OVERRIDE and get "del" flashing but no "rst"...
View ArticleVPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset...
View ArticleHow to get into MOdE
When I press set and Override the timer will not go into rst. I DEL flashes and when it stops blinking I let go and the clock comes onto the LCD display. I can't get the timer in PRO mode of...
View ArticleVPT24-1P
VPT24-1P Replacing a mechanical light timer which connected solely to a hot lead and the load lead (for lighting only). Wired the new timer per diagram - hot box lead to black; box load lead to red;...
View ArticleLTB60-1LZ 3-Way Wiring
I'm trying to wire up this with the corresponding VP0SR-1LZ. The wiring diagrams match up perfectly for the Remote Switch, but the LTB60 is asking for 5 wires and I only have 4 (including the ground)....
View ArticleVPOSR-1L 4-way help
My goal is to add a LBT02 timer to a hall circuit with three switches. I intend to use a couple of VPOSR-1L switches with the timer. The box with the old 4-way switch has two 2 conductor wires. The...
View ArticleQuestion on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a...
View ArticleVPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset...
View ArticleVPT24-1P wiring diagram
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box...
View ArticleProblem when installing VPT24-1P
I am trying to install a Leviton VPT24-1P Digital Timer Switch: Hi I'm trying to install the timer swtich on the right most light switch of a 3-light switch electric box....
View ArticleHelp installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the...
View ArticleI am replacing a single pole switch with a VPT 24
The switch I am replacing has only two black wires going to the switch but there was a white (neutral I believe) wire in the box going to another swicth. I connected the wiring exactly as shown for the...
View ArticleProblems with Leviton VPT24
i just had a new Leviton vpt24 installed, but for some reason it isnt controlling my light that i hooked it up to. Also, the backlight wont illuminate. Any ideas?
View ArticleDon't see how to configure the timer to meet my needs.
I have a vpr24-1PZ and set two events. The first has the lights turning on at sunset and turning off at 11:00PM. That is simple. The second turned on the lights at 6:25 AM and turned them off at...
View ArticleQuestion on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a...
View ArticleHelp installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the...
View ArticleVPT24-1P Timer goes into permanent override after end of event
Hello, I programmed one event to turn on the porch lights daily from sundown to 11pm in PRO mode. But the timer automatically jumps to permanent override every night after the lights go off at the...
View Article