Vizia VPT24
I bought this timer to control my exterior lights. My exterior lights are controlled by 2 switches (3 way). I noticed on the box that it says to control the fixture from two locations I need the...
View ArticleVPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset...
View ArticleCan't figure out how to wire VPT24-1PZ with Matching Remote
I am trying to replace two existing 3-pole switches with a Leviton vizia+ (VPT24-1PZ) along with a Matching Switch Remote (VP0SR-1LZ) but have been unsuccessful. I can get the switch screen to power...
View ArticleUnable to Switch to Pro Mode
I installed in STD mode and then realized I should have done in PRO to use sun up / sun down. How can I switch to PRO? I tried holding SET and then OVERRIDE and get "del" flashing but no "rst"...
View Article3 way wiring installation with VPT24-1P
I am trying to install a VPT024 with a remote. In my case I have power through the fixture and a 3 way switch on either end. All of the diagrams I see have an incoming line and outgoing line, I...
View ArticleVPT24-1PZ how to factory reset all setting
So I have problem cuz I tryed to many time clock setting but VPT24 clock goes wrong soon How can I factory reset all setting. or Is this VPT24 is broken???
View ArticleQuestion about installing the VPT24-1PZ
Hi, I am attempting to install this switch but have run into some problems. The switch is in a panel with two other switches. One is a three way and the other two are single poles (at least I think...
View ArticleLeviton Vizia
Is there any way to keep the screen lit on all the time? -Thanks in advance!
View ArticleQuestion on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a...
View ArticleHelp installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the...
View ArticleWiring LTB60-1LZ does not work, stops other switch
I have a bathroom with a three-switch panel (left: vanity lights, middle: bathroom fan light, right: bathroom fan). I wanted to install a LTB60-1LZ for the fan so I connected it as follows: -...
View ArticleProgramming the VPT24-1P
I have successfully installed & programmed my VPT24-1P, in PRO mode for automatic turn on at sundown and turnoff at sunup, but the "temporary override when flashing" is flashing. Why and what does...
View ArticleCan two LTB60-1LZ switches be installed in a 3-Way configuration
Can two LTB60-1LZ switches be installed in a 3-Way configuration, one in each bathroom, to operate a central fan, and if so, what does the wiring diagram look like?
View ArticleHow do I install a timer delay switch on an end of run?
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red. It is an end of run switch, so the white wire is actually the hot wire and the black runs...
View ArticleQuestion on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a...
View ArticleProblem when installing VPT24-1P
I am trying to install a Leviton VPT24-1P Digital Timer Switch: Hi I'm trying to install the timer swtich on the right most light switch of a 3-light switch electric box....
View ArticleSharing a Neutral wire may cause improper operation.
In the troubleshooting it mentions that sharing a neutral wire may cause improper operation, what does this mean? I have a timer wired as seen in the attached image and it does not turn on, the LED...
View ArticleVPT24-1PZ Astronomical Program not working
Hello, We've purchased a VPT24-1PZ timer to drive the exterior lights on our building. A picture of the box is below. The installation seems correct. When pressing the toggle cover on the timer...
View Article