VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset...
View ArticleVPT24-1PZ Stuck on Event 1???
I have 2 events programmed and I can't seem to get Event 2 to stay as the active event; it keeps staying on Event 1?? I followed the instructions but I can't seem to make the light switch to stay on...
View ArticleVPT24 - Is after midnight considered the next day?
Hello, This will probably sound like a stupid question, but I haven't been able to find anything about this yet. In short: Does a day extend past midnight? Say I want to turn on the lights on...
View ArticleVPT24-1PZ Astronomical Program not working
Hello, We've purchased a VPT24-1PZ timer to drive the exterior lights on our building. A picture of the box is below. The installation seems correct. When pressing the toggle cover on the timer...
View ArticleLow temperature operation of Leviton VPT24-1PZ
Hi, I recently purchased a Leviton VPT24-1PZ timer switch to operate some outdoor lights. The concern I have is that in our home, the switch that controls the outdoor lights is located inside the...
View ArticleVPT24 as a 3-way replacement
I am trying to use the VPT24-1P to replace an existing 3-way switch. My existing switch, and the mate, are both 3-way toggle switches. They have a Red, Black, Green and White connected to them, with...
View ArticleVPT24-1PZ how to factory reset all setting
So I have problem cuz I tryed to many time clock setting but VPT24 clock goes wrong soon How can I factory reset all setting. or Is this VPT24 is broken???
View ArticleDoes Leviton offer a timer that corrects for Daylight Savings?
Does Leviton offer a timer that corrects for Daylight Savings?
View ArticleHow do I install a timer delay switch on an end of run?
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red. It is an end of run switch, so the white wire is actually the hot wire and the black runs...
View ArticleQuestion on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a...
View ArticleProblem with VPT24-1PZ Always switching to off mode
I have programmed my timer with one schedule to turn the lights on and off at the specified times (Turn on 6pm, turn off 12am). With the timer set to auto mode, at the end of each program period, the...
View Articletimer switch and GFCI
I bought a 6124H-W electronic timer switch a couple of years ago. I have a circuit that runs from the house to the street with a post light, outlet, and low-voltage transformer feeding some path...
View ArticleLTB60 Wiring Question
In the box in the upstairs bathroom there are four bundles of wires. The current switches (both light and fan) each have one hot wire entering them and a then black wire going back into the tied...
View ArticleLTB30-1LZ - 3-way Wiring with Vizia + Matching Remote switch (w/LED) ISSUES
Hi, I just install a LTB30-1LZ with the 3-way wiring with Vizia + Matching Remote switch (Step 4c in the instruction sheet) but I have a issue. The Timer work and my lightswitch also work. I only...
View ArticleVPT24-1PZ Astronomical Program not working
Hello, We've purchased a VPT24-1PZ timer to drive the exterior lights on our building. A picture of the box is below. The installation seems correct. When pressing the toggle cover on the timer...
View ArticleLTB60-1LZ 3-Way Wiring
I'm trying to wire up this with the corresponding VP0SR-1LZ. The wiring diagrams match up perfectly for the Remote Switch, but the LTB60 is asking for 5 wires and I only have 4 (including the ground)....
View ArticleHow do I install a timer delay switch on an end of run?
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red. It is an end of run switch, so the white wire is actually the hot wire and the black runs...
View ArticleVPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset...
View ArticleHelp installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the...
View ArticleVPT24-1P wiring diagram
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box...
View Article