I have a vpr24-1PZ and set two events. The first has the lights turning on at sunset and turning off at 11:00PM. That is simple. The second turned on the lights at 6:25 AM and turned them off at sunrise. (Turns on exterior
↧
Don't see how to configure the timer to meet my needs.
↧
LTB30 Timer Installation for Bathroom Fan
Hi guys, I purchased a Leviton LTB30 and tried to installed it for my bathroom fan. However I'm confused by my bathroom fan wiring. I'm not sure if this is a 3 way or single pole configuration. This is the existing wiring. 3 sets of wires
↧
↧
Help installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the copper wire in the wall a black
↧
VPT24-1P wiring diagram
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box but what do i hook up the red/yellow wire too? how
↧
VPT24 Installation
My existing light switch did not have a neutral connection, but I have tapped into the white (neutral?) wires inside the box. Unfortunately, this has not done the trick as I cannot get the timer to work. I am getting the Battery Power (no
↧
↧
How do I install a timer delay switch on an end of run?
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red. It is an end of run switch, so the white wire is actually the hot wire and the black runs back to the lights. How do I do it?
↧
Question on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a fan. The old switch has two black
↧
Problem when installing VPT24-1P
I am trying to install a Leviton VPT24-1P Digital Timer Switch: Hi I'm trying to install the timer swtich on the right most light switch of a 3-light switch electric box. ----------------------------------------------------- Original box setup: From
↧
VPT24-1P Timer goes into permanent override after end of event
Hello, I programmed one event to turn on the porch lights daily from sundown to 11pm in PRO mode. But the timer automatically jumps to permanent override every night after the lights go off at the preset time and won't go back to timer mode
↧
↧
VPT24-1P makes loud clicking sounds and the light blinks on and off rapidly.
I installed a VPT24-1P and now light is very dim and when I turn it off it blinks rapidly and the switch makes a loud clicking sound. When I leave it on, after a few minutes it will also blink on and off rapidly. I am using an LED light but, from what I
↧
Setting on off time correctly
This should be fairly simple. I want the lights to come on at sunset everyday, this seems fairly straightforward. I Wat the lights to turn off at the same time everyday, say 2am and not sunrise. How would I program that? thanks in advance
↧
Leviton 6161-W Decora 4-Level Step Dimmer
I just bought the Levition No. 6161 4-Level dimmer switch and wanted to know if it will work with Dimmable LED lights. The switch hums when I turn it on with dimmable LEDs lights. Thank you for your answers to my question.
↧
VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset setting is for? Is it used to
↧
↧
Help installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the copper wire in the wall a black
↧
VPT24-1P wiring diagram
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box but what do i hook up the red/yellow wire too? how
↧
LTB30 Timer Installation for Bathroom Fan
Hi guys, I purchased a Leviton LTB30 and tried to installed it for my bathroom fan. However I'm confused by my bathroom fan wiring. I'm not sure if this is a 3 way or single pole configuration. This is the existing wiring. 3 sets of wires
↧
VPT24 issue. stopped working few hours after installation
Hi, I just purchased today a VPT24 switch, installed it, got it working. A friend of mine came to see me and few hours later, went to check the nice job I did.... The switch doesn't have lcd anymore, if i press the MENU button
↧
↧
VPT24-1P just stopped working
I have been using the timer for over 3 years now. the other day it just stopped working. The screen went blank. You can not even turn the lights on and off manually. can you suggest something?
↧
VPT24-1PZ Astronomical Program not working
Hello, We've purchased a VPT24-1PZ timer to drive the exterior lights on our building. A picture of the box is below. The installation seems correct. When pressing the toggle cover on the timer switch the lights turn
↧
Problems with Leviton VPT24
i just had a new Leviton vpt24 installed, but for some reason it isnt controlling my light that i hooked it up to. Also, the backlight wont illuminate. Any ideas?
↧