Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a fan. The old switch has two black
↧
Question on LTB60-1LZ Wiring
↧
Leviton 6161-W Decora 4-Level Step Dimmer
I just bought the Levition No. 6161 4-Level dimmer switch and wanted to know if it will work with Dimmable LED lights. The switch hums when I turn it on with dimmable LEDs lights. Thank you for your answers to my question.
↧
↧
Help installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the copper wire in the wall a black
↧
VPT24-1PZ Stuck on Event 1???
I have 2 events programmed and I can't seem to get Event 2 to stay as the active event; it keeps staying on Event 1?? I followed the instructions but I can't seem to make the light switch to stay on Event 2??
↧
LTB60-1LZ 3-Way Wiring
I'm trying to wire up this with the corresponding VP0SR-1LZ. The wiring diagrams match up perfectly for the Remote Switch, but the LTB60 is asking for 5 wires and I only have 4 (including the ground). I've identified the ground, 2nd traveler
↧
↧
LTB30-1LZ - 3-way Wiring with Vizia + Matching Remote switch (w/LED) ISSUES
Hi, I just install a LTB30-1LZ with the 3-way wiring with Vizia + Matching Remote switch (Step 4c in the instruction sheet) but I have a issue. The Timer work and my lightswitch also work. I only have one wire with a load, I can't use the
↧
VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset setting is for? Is it used to
↧
How do I install a timer delay switch on an end of run?
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red. It is an end of run switch, so the white wire is actually the hot wire and the black runs back to the lights. How do I do it?
↧
VPT24-1PZ Light Switch Programable Timer
I recently purchased a programable light switch timer, VPT24-1PZ, to replace the existing light switch that is currently installed.. I tried installing it and the screen would not start up or the light would not switch on. The existing wires
↧
↧
VPT24-1P wiring diagram
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box but what do i hook up the red/yellow wire too? how
↧
timer switch and GFCI
I bought a 6124H-W electronic timer switch a couple of years ago. I have a circuit that runs from the house to the street with a post light, outlet, and low-voltage transformer feeding some path lights, and wanted to put the lights on a
↧
VPT24-1PZ Astronomical Program not working
Hello, We've purchased a VPT24-1PZ timer to drive the exterior lights on our building. A picture of the box is below. The installation seems correct. When pressing the toggle cover on the timer switch the lights turn
↧
Programmable timer
Does Leviton offer a programmable timer (similar to the VPT24-1PZ) that can be used to control operation of a whole house fan including both high the low speed operation?
↧
↧
Question on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a fan. The old switch has two black
↧
VPT24-1P makes loud clicking sounds and the light blinks on and off rapidly.
I installed a VPT24-1P and now light is very dim and when I turn it off it blinks rapidly and the switch makes a loud clicking sound. When I leave it on, after a few minutes it will also blink on and off rapidly. I am using an LED light but, from what I
↧
Setting on off time correctly
This should be fairly simple. I want the lights to come on at sunset everyday, this seems fairly straightforward. I Wat the lights to turn off at the same time everyday, say 2am and not sunrise. How would I program that? thanks in advance
↧
Help installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the copper wire in the wall a black
↧
↧
LTB30-1LZ - 3-way Wiring with Vizia + Matching Remote switch (w/LED) ISSUES
Hi, I just install a LTB30-1LZ with the 3-way wiring with Vizia + Matching Remote switch (Step 4c in the instruction sheet) but I have a issue. The Timer work and my lightswitch also work. I only have one wire with a load, I can't use the
↧
VPOSR-1L 4-way help
My goal is to add a LBT02 timer to a hall circuit with three switches. I intend to use a couple of VPOSR-1L switches with the timer. The box with the old 4-way switch has two 2 conductor wires. The instructions assume the box has a pair of 3
↧
VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset setting is for? Is it used to
↧