Hi guys, I purchased a Leviton LTB30 and tried to installed it for my bathroom fan. However I'm confused by my bathroom fan wiring. I'm not sure if this is a 3 way or single pole configuration. This is the existing wiring. 3 sets of wires
↧
LTB30 Timer Installation for Bathroom Fan
↧
timer switch and GFCI
I bought a 6124H-W electronic timer switch a couple of years ago. I have a circuit that runs from the house to the street with a post light, outlet, and low-voltage transformer feeding some path lights, and wanted to put the lights on a
↧
↧
VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset setting is for? Is it used to
↧
How do I install a timer delay switch on an end of run?
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red. It is an end of run switch, so the white wire is actually the hot wire and the black runs back to the lights. How do I do it?
↧
Help installing VPT24-1P Timer switch
THis is what I am seeing inside my box in the wall - A copper ground wire A black wire A red wire on this new unit I see the following green wire - I am pretty certain this connects to the copper wire in the wall a black
↧
↧
VPT24-1P wiring diagram
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box but what do i hook up the red/yellow wire too? how
↧
Don't see how to configure the timer to meet my needs.
I have a vpr24-1PZ and set two events. The first has the lights turning on at sunset and turning off at 11:00PM. That is simple. The second turned on the lights at 6:25 AM and turned them off at sunrise. (Turns on exterior
↧
vpt24-1p installation, power from light
What is the wiring sequence when power is coming from the light. I have a 14/2 wire coming into the swicth box. the white wire coming into the switch box shows power. My timer has a black line wire, a white neutral wire, a red load wire , a ground and a
↧
VPT24-1PZ how to factory reset all setting
So I have problem cuz I tryed to many time clock setting but VPT24 clock goes wrong soon How can I factory reset all setting. or Is this VPT24 is broken???
↧
↧
Problem when installing VPT24-1P
I am trying to install a Leviton VPT24-1P Digital Timer Switch: Hi I'm trying to install the timer swtich on the right most light switch of a 3-light switch electric box. ----------------------------------------------------- Original box setup: From
↧
How do I install a timer delay switch on an end of run?
I want to install a LTB02-1LZ countdown timer, but there are only two wires - one black and one white, no red. It is an end of run switch, so the white wire is actually the hot wire and the black runs back to the lights. How do I do it?
↧
LTB60-1LZ 3-Way Wiring
I'm trying to wire up this with the corresponding VP0SR-1LZ. The wiring diagrams match up perfectly for the Remote Switch, but the LTB60 is asking for 5 wires and I only have 4 (including the ground). I've identified the ground, 2nd traveler
↧
VPT24-1P Timer goes into permanent override after end of event
Hello, I programmed one event to turn on the porch lights daily from sundown to 11pm in PRO mode. But the timer automatically jumps to permanent override every night after the lights go off at the preset time and won't go back to timer mode
↧
↧
VPT24 with a Dimmer Switch??
I would like to use a VPT24 to control some incandescent lights that are now on a dimmer switch. But I also want to keep the dimmer function. Obviously, the VT24 does not contain a dimmer. Question: Can I wire the existing dimmer on the load side
↧
Setting on off time correctly
This should be fairly simple. I want the lights to come on at sunset everyday, this seems fairly straightforward. I Wat the lights to turn off at the same time everyday, say 2am and not sunrise. How would I program that? thanks in advance
↧
Question on LTB60-1LZ Wiring
Hi: I am trying to install a LTB60-1LZ countdown timer into a 4 gang box. The box is in a bathroom and near a GFCI outlet. The switch I am replacing is a 2 wire, three speed motor control for a fan. The old switch has two black
↧
VPT24-1PZ Astronomical Program not working
Hello, We've purchased a VPT24-1PZ timer to drive the exterior lights on our building. A picture of the box is below. The installation seems correct. When pressing the toggle cover on the timer switch the lights turn
↧
↧
VPT24-1PZ, Pro Mode, Sunup/Sundown offset time.
Hi, I installed this timer, and it's working. I have the porch lights come on at 6 am, and off at sunrise, then on at sunset and off at 11 pm. I like it. My question is on what the offset setting is for? Is it used to
↧
VPT24-1P wiring diagram
I'm trying to hook up my VPT24-1P timer on a three way system. the big problem is on both switches already installed i only have three wires. red, white and black. the ground is in the back of the box but what do i hook up the red/yellow wire too? how
↧
LTB30-1LZ - 3-way Wiring with Vizia + Matching Remote switch (w/LED) ISSUES
Hi, I just install a LTB30-1LZ with the 3-way wiring with Vizia + Matching Remote switch (Step 4c in the instruction sheet) but I have a issue. The Timer work and my lightswitch also work. I only have one wire with a load, I can't use the
↧